Engineering Graphics & BED part 1
Engineering Graphics (EG)
basic engineering drawing (BED)
Q. 1 Which of the following represent full scale?
(A) 10:1
(B) 20:1 (C) 1:1 (D) 1:10
ans
C
Q. 2 Which is the line used for visible outlines?
(A) Continuous thin (B) Continuous thick (C) Chain thin line (D) Short zigzag thin
ans B
Q.
3 When the line is parallel to VP and
perpendicular to HP, we can get its true length in ___________.
(A) Top view
(B) Front view (C) Side
view (D) Front view & Side view
ans
D
Q.
4 Which of the following position is not
possible for a plane?
(A) Parallel to both HP and VP (B) Perpendicular to HP and parallel to
VP (C) Perpendicular to VP and
parallel to HP (D) Perpendicular to
both HP and VP
ans
A
Q.
5 A tetrahedron has ____equal
rectangular faces
(A) 0
(B) 2 (C) 3 (D) 4
ans
A
Q.
6 If the value of Eccentricity is not
equal to 1 curve will be_________
(A) Ellipse or Circle (B) Parabola or Ellipse (C) Parabola or Hyperbola (D) Ellipse or Hyperbola
ans
D
Q.
7 The side view of an object is drawn in
___________.
(A) Side plane (B) Horizontal plane (C) Profile plane (D) Vertical plane
ans
C
Q. 2 When the drawing are drawn smaller than the actual size of object then scale is known as
(A) Enlarged Scale (B) Reduced Scale (C) Full Scale (D) Standard scale
ans
B
Q. 3 A curved traced out by a point which moves uniformly both about the Centre and at the same time away or towards the Centre is known as
(A) Involute
(B) Cycloid (C) Arche median
spiral (D) Ellipse
ans C
Q. 4 If the object lies in the fourth quadrant, its position with respect to reference plane will be
(A) In front of V.P. and above H.P (B) Behind V.P. and below H.P. (C) In front of V.P. and below H.P. (D) Behind V.P. and above H.P.
ans
C
Q. 5 10 mm Length of line in Isometric projection will be equal to
(A) 10 mm
(B) 8.15 mm (C) 12.26 mm (D) 7.07 mm
ans
B
Q. 6 When a right regular cone is cut by a plane parallel to base the shape of section obtained is
(A) Ellipse
(B) Parabola (C) Triangle (D) Circle
ans
D
Q. 7 A line having length of L is resting on HP on one end and other end is in VP and parallel to profile plan then summation of angle made by line with HP and VP is
(A) 60?
(B) 90? (C) 30? (D) 45?
ans B
Q.
1 A short break line is used to indicate
a
(A) broken part (B) part to be broken (C) long part of uniform cross section (D) short part of non-uniform cross
section
ans
B
Q. 2 The type of line used to indicate a cutting plane is
(A) Dashed
(B) long dashed dotted (C) long
dashed double dotted (D) continuous
freehand
ans
B
Q.
3 The size of the drawing drawn to scale
2:1 will be ____________ the actual size.
(A) Same as
(B) twice of (C) half of (D) none of a,b, and c
ans
B
Q.
4 If an area of Y2 is represented by an
area of X2 on a drawing, then the RF is equal to
(A) X/Y
(B) X2/Y2 (C) vX / vY (D) vX2 / vY2
ans
B
Q.
5 Boyle’s law, PV = constant generates a
curve which is a
(A) Hyperbola (B) rectangular hyperbola (C) parabola (D) rectangular parabola
ans
B
Q.
6 The gear tooth profile is in the form
of
(A) parabola
(B) involute (C) spiral (D) helix
ans
B
Q.
7 The line joining any point on an
Archimedean spiral with the pole is called the
(A) shortest radius (B) radius vector (C) vectorial angle (D) convolution
ans
B
Q.
8 In the orthographic projections, F.V.
is projected on
(A) H.P.
(B) V.P. (C) XY (D) GL
ans
B
Q.
9 The top view of a rectangular shaped
room will show
(A) length and height (B) length and width (C) width and height (D) height only
ans
B
Q.
10 If O + Ø = 900, then which of the
following statements is CORRECT?
(A) a = ß = 900 (B) side view = TL (C) FV is perpendicular to XY (D) All of the above
ans
D
Q.
11 To obtain the true shape of the
section of a solid, the auxiliary plane is set
(A) inclined at 450 to cutting plane (B) perpendicular to the cutting plane (C) parallel to cutting plane (D) parallel to XY
ans
C
Q.
12 Compare to actual diameter, the
isometric diameter of the sphere is
(A) equal
(B) smaller (C) greater (D) none
ans
C
Q.
13 The height of the tetrahedron of 40
mm sides will be _________ 40 mm.
(A) equal to
(B) less than (C) greater than (D) half of
ans
B
Q.
14 In Isometric projection, the length
or width of the object is drawn at _________ to the horizontal reference line.
(A) 300
(B) 450 (C) 900 (D) 1200
ans
A
0 comments: